首页|期刊简介|投稿指南|分类索引|刊文选读|订阅指南|资料|样刊邮寄查询|常见问题解答|联系我们
李叶文,李宗轩,刘瑞婧,等. 空间光学遥感器长条形反射镜集成优化设计[J]. 科学技术与工程, 2019, 19(35): 375-381.
LI Ye-wen,LIU Rui-jing,et al.Integrated Design of Rectangular Mirror for Space Optical Remote Sensor[J].Science Technology and Engineering,2019,19(35):375-381.
空间光学遥感器长条形反射镜集成优化设计
Integrated Design of Rectangular Mirror for Space Optical Remote Sensor
投稿时间:2019-04-22  修订日期:2019-09-01
DOI:
中文关键词:  空间相机  轻量化设计  集成优化  灵敏度分析  尺寸优化
英文关键词:space camera  lightweight design  integrated optimization  sensitivity analysis  size optimization
基金项目:吉林省科技发展计划项目(No.20180414066GH)
              
作者单位
李叶文 中国科学院长春光学精密机械与物理研究所
中国科学院大学
李宗轩 中国科学院长春光学精密机械与物理研究所
刘瑞婧 中国科学院长春光学精密机械与物理研究所
中国科学院大学
宋伟阳 中国科学院长春光学精密机械与物理研究所
中国科学院大学
张丽敏 中国科学院长春光学精密机械与物理研究所
摘要点击次数: 88
全文下载次数: 22
中文摘要:
      针对空间光学遥感器离轴三反光学系统主镜的高轻量化率、高面形精度要求,提出了一种长条形反射镜集成优化的设计方法。首先利用变密度的拓扑优化方法分别得到刚度最大化和一阶频率最大化的反射镜拓扑模型,综合两种拓扑模型得到了反射镜的集成设计方案。然后提出了基于镜面变形值的镜体加强筋变量拓展优化方法,进行了设计变量的灵敏度分析,并对反射镜局部加强筋进行了多变量尺寸优化,得到了该长条形反射镜的最佳轻量化结构。最后对优化结果进行了有限元分析,仿真结果表明反射镜在优化后的面形精度有了显著提升,镜体质量仅为8.65 kg,与实心镜体相比轻量化率达到了80.9%。在Z向1 G重力作用下,镜面面形精度PV值为23.70 nm, RMS值为4.54 nm,该优化方法能很好的满足设计要求。
英文摘要:
      An integrated optimization design method for rectangular mirror was applied in this paper aiming at the requirements of high lightweight ratio and high surface figure quality of the primary mirror in off-axis three-mirror optical system for space optical remote sensor. Firstly, the topology optimization method with variable density was used to obtain the mirror topology models with maximum stiffness and maximum first-order frequency respectively, the integrated design scheme of the mirror was obtained by synthesizing the two topology models. Then, a variable expansion optimization method of the mirror ribs based on the mirror deformation value was proposed, the sensitivity analysis of the design variables was carried out, and the multi-variable size optimization of the local ribs of the mirror was optimized, Finally, the optimization result was analyzed by finite element method. The result of finite element simulation analysis shows that the surface figure of the mirror after optimization has been significantly improved. The weight of the mirror after size optimization design is only 8.65 kg, resulted in a weight reduction of about 80.9% compared to the initial solid mirror. Under the loading condition of 1 G gravity in Z direction, The PV value is 23.70 nm, with RMS is 4.54 nm. which meets the design requirements.
查看全文  查看/发表评论  下载PDF阅读器
关闭
你是第27548595位访问者
版权所有:科学技术与工程编辑部
主管:中国科学技术协会    主办:中国技术经济学会
Tel:(010)62118920 E-mail:stae@vip.163.com
京ICP备05035734号-4
技术支持:本系统由北京勤云科技发展有限公司设计

京公网安备 11010802029091号